CROWN XLS-802 PA Amplifier 2 X 800W @ 4Ohms

Professional Stereo Power Amplifier (800w/ch @ 4 ohms)

XLS Series Overview

The XLS Series of power
amplifiers from Crown represents a new era in affordable, quality power
amplification. The line consists of three models in a uniform, rugged
chassis, incorporating the best of tried-and-true design principles and
innovative features. XLS Series amplifiers are professional stereo
power amplifiers engineered to meet demanding audio
requirements—reliably and within budget. Plus, every XLS Series
amplifier is backed by Crown’s unequaled Three-Year, No-Fault,
Fully-Transferrable Warranty that covers everything. With over five
decades of experience designing and building rock-solid products, Crown
is the standard in amp technology. So check out the affordable, Crown
XLS Series. They are a powerful argument for quality and value!

Reliable design incorporates many popular features

*
Selectable high-pass filter on each channel enables amplifier to work
more efficiently when full band-width is not required.

* Pair of linear optocoupler clip limiters protects loudspeakers from being overdriven.

* Housed in a rugged, all-steel 2U chassis.

* Efficient forced-air fan prevents excessive thermal buildup.

* Electronically balanced XLR inputs and touch-proof binding post outputs.

*
Features precision detented level controls, power switch, and four
LEDs, which indicate clip for each channel, power and fault conditions.

* Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications.

Specifications

Performance
Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V.

Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –0.8 dB.

Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power: >98 dB.
No weighting, below rated power: >93 dB.

Total Harmonic Distortion (THD): <0.5%.

Intermodulation Distortion (IMD):
(60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.

Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.

Crosstalk (below rated power)
at 1 kHz: –76 dB. at 20 kHz: –58 dB.

Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.

Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.

AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC
Controls

Level: Two front-panel rotary level controls, one for each channel.

Power: Front-panel switch; on when in the IN position.

Circuit Breaker: Back-panel breaker provides overload protection.

Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode.
Indicators

Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.

Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.

Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.

Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.
Input/Output

Input Connectors: One per channel; back-panel three-pin female XLR input connectors.

Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.
One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)
Protection

XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.
Construction

Ventilation: Flow-through ventilation from front to back.

Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.

Air Volume Requirements (per minute per unit): 80.15 ft©¯ (2.27 m©¯).

Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2-inch (38.6-cm) depth.

Weight
Net Weight:
XLS-202: 23.0 lb (10.4 kg)
XLS-402: 25.7 lb (11.7 kg)
XLS-602: 29.0 lb (13.2 kg)
XLS-802: 35.5 lb (16.1 kg)

Shipping Weight:
XLS-202: 28.0 lb (12.7 kg)
XLS-402: 30.7 lb (13.9 kg)
XLS-602: 34.0 lb (15.4 kg)
XLS-802: 40.5 lb (18.4 kg)

Approximate Weight 0.0kg

Related Products

DBX DRIVERACK PA EQ & Speaker Management Processor
| more

ROAD READY 2U DELUXE AMPLIFIER CASE - 18" Depth
$339.00 | more

ROAD READY 4U DELUXE AMPLIFIER CASE - 18" Depth
$399.00 | more